5
Cisco Anyconnect via OpenVPN tunnel on Windowsview story

http://serverfault.com – I'm trying to connect to a Cisco VPN using an USB-tethered connection using OpenVPN. The moment I enable Cisco AnyConnect, traffic stops on OpenVPN interface, resulting in disconnection. OS is Windows 7 64-bit. Any ideas? (HowTos)

5
adding another security layer on top of openvpnview story

http://serverfault.com – not sure if this is the right stackexchange site, but here it goes. I've set up a VPS that handles mail, files, jabber, etc. all these services are available only to the local network that openvpn creates, so like only on 10.55.66.xx. (HowTos)

6
Debian: IPv6-in-IPv4 over OpenVPNview story

http://serverfault.com – Following (roughly) the instructions https://www.zagbot.com/openvpn_ipv6_tunnel.html at I now have the following: Client martin@theoria:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:50:8d:b3:fd:f4 inet addr:192.168.0.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::250:8dff:feb3:fdf4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metri (HowTos)

13
Squid proxy forward traffic through openvpn server # linode VPSview story

https://www.centos.org – sandeep77897 - Welcome to the CentOS fora. Please see the recommended reading for new users linked in my signature.After reading those links you should realize why you should no... [by pschaff] (Distributions)

10
Getting OpenVPN to work with XFCE on Xubuntu?view story

http://askubuntu.com – I'm trying to get OpenVPN to work properly on my install of Xubuntu 11.10. So far, no luck. (HowTos)

4
[ubuntu] OpenVPN certain trafficview story

http://ubuntuforums.org – Here's a basic layout of what I have: Remote server in Chicago is mail server, backup server and public facing FTP server due to higher bandwidth. I want the remote server to VPN back to a local server so that on the local network it is addressable on the internal network (say it has an address of 10.8.0.6) and then nightly a script will go and rsync data from local server to the remote. (Hardware)

3
route all internet traffic via a virtual tap device and a public server on windowsview story

http://serverfault.com – We want to route all traffic from one pc to a local virtual device (TAP-Win32 Adapter which is also used by OpenVPN) and then from there to another tap device on a public server. (HowTos)

12
OpenVPN performance terrible to other machines on server's subnetview story

http://serverfault.com – I'm having a lot of trouble getting OpenVPN performance to be what I would expect with my new OpenVPN setup. The network looks like this: Home LAN 172.16.1.0/24 VPN Clients (10.8.0.0/24) -> Airport Extreme (forwarding OpenVPN port) -> OpenVPN Server (listening on OpenVPN port 1294) -> Home iMac -> NAS Box I am using routing, with the following config file. (HowTos)

13
[ubuntu] ./build-dh taking not long enough [OpenVPN]view story

http://ubuntuforums.org – Hi, I tried to configure my own OpenVPN server, but build-dh only takes about 30 seconds, and creating the keys with pkitool takes less than 3 seconds. The same issue was discussed here but that didn't work for me. Maybe I should mention that I got a "unable to write 'random state'" error message when I first tried to execute build-dh, so i deleted the .rnd file in my home direc (Hardware)

5
OpenVPN connects with no warnings but cannot pingview story

http://serverfault.com – The server and client can ping themselves but not each other. I have OpenVPN running on Windows 2008 Server and Windows 7. The computers connect just fine, the server gets 10.8.0.1 with a gateway of 10.8.0.2 and the client gets 10.8.0.10 with a gateway of 10.8.0.9. It's in tunnel mode. (HowTos)