8

Wlan0 Static Ip bridge

view full story
linux-howto

http://unix.stackexchange.com – EDIT: Even taking br0 out, still cannot get a static IP connection. I had the following /etc/network/interfaces configuration and it was working auto lo iface lo inet loopback auto eth0 iface etho inet manual allow-hotplug wlan0 auto wlan0 iface wlan0 inet dhcp wpa-ssid "xxxx" wpa-pskl "xxxx" auto br0 iface br0 inet dhcp bridge_ports wlan0 eth0 I changed the config for wlan0 to the following and now it doesn't work auto wlan0 iface wlan0 inet static address 192.168.1.124 netmask 255.255.255.0 network 192.168.1.1 broadcast 192.168.1.255 wpa-ssid "xxxx" wpa-pskl "xxxx I am trying to s (HowTos)

Songlist's picture
Submitted by Songlist on 01/27/2013 – Made popular on 01/27/2013

Stories similar to Wlan0 Static Ip bridge

I have a Raspberry Pi with two USB wlan adapters. wlan0 is configured with DHCP and wlan1 is configured with a static IP address. But wlan1 never gets it's IP address after boot and the network does not work properly.

Dear all,

I'm trying to setup an hot spot wifi from a board running ubuntu.

I've installed hostapd and udhcpd.

This is my /etc/hostapd/hostapd.conf

Code: interface=wlan0 driver=nl80211 ssid=armSSID auth_algs=1 channel=1 wpa=0 ignore_broadcast_ssid=0 This is my /etc/network/interfaces

Code: auto lo iface lo inet loopback

auto eth0 iface etho inet dhcp

iface wlan0 inet static &nbsp

Hi, yesterday I've done a release upgrade from 10.4.1 LTS to 10.10 and I faced the following issues:

1) br0 does not bridge anymore eth0 and wlan0 (I have a DNMA92 wireless card that runs ath9k drivers) at startup even if specified in /etc/network/interfaces:

Code: auto lo iface lo inet loopback pre-up /sbin/iptables-restore < /etc/network/firewall-rules.conf

# The primary network interfac

I am running ubuntu 12.04 minimal on a beagle bone.I am trying to get the wifi running at boot time . But the ip address does not seem to be assigned to it.

I have debian hosts which are connected through trunk port on 5 different vlans. But this host respond to arp "who-has" requests of all of their differents ip.

I want to use my desktop with a wired ethernet connection (eth0) to operate my USB Wifi Adapter (wlan0) as a non-adhoc access point (so my android can connect to it).

After MUCH searching, I finally found a method that works with about 95% of what I want.

I modified "/etc/network/interfaces" to contain:

auto lo iface lo inet loopback

auto eth0 iface eth0 inet manual

auto br0 iface br0 i

I am running Ubuntu Server 12.04. I have a wireless USB card. When I begin the boot process I see:

Waiting for network configuration

It turns out that the network never comes up. But once I get to the command line, if I type: ifup wlan0, then I have network access.

I am trying to configure my ethernet and wireless connections in Xubuntu 12.04 and i tried to set them up by configuring only /etc/networking/interfaces like below.

auto eth0 iface eth0 inet static address 192.168.1.11 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.12 gateway 192.168.1.1 wpa-ssid lausi wpa-psk brezje56

auto wlan0 iface wlan0 inet static

I have 3 network cards installed in my ubuntu 10.04 server and I want to configure Internet sharing and file sharing on eth1 for wired users and wlan0 for wireless users.

Static ip: eth0: 192.168.1.1 eth1: 10.0.0.15 wlan0: 10.0.0.20

/etc/network/interfaces

# The loopback network interface auto lo iface lo inet loopback

# The primary network interface auto eth0 iface eth0 inet static address 19