13

[ubuntu] Serial PCI Card + Serial Modem

view full story
linux-howto

http://ubuntuforums.org – Hi Guys I've been using Ubuntu 11.10 on my Work PC, Part of my job occasionally requires me to dial into other machines. Under Windows I have a wide selection of internal PCI modems/USB Modems and Even a serial modem (That I've never used) Anyhow, Its part of my day to day tasks and I need that dial up connection. In days of Old on Ubuntu 7.10 and prior all my modems were auto detected and I'd simply go to the gnome network panel, enter the number click dial and all was good. Under Ubuntu with Gnome3 or Unity I open "Network" and it comes up with just "Wired" a (Hardware)

linuxfan's picture
Submitted by linuxfan on 04/24/2012 – Made popular on 04/24/2012

Stories similar to [ubuntu] Serial PCI Card + Serial Modem

wvdial might also be a workaround, if one does not like to downgrade. In my case, I had to unset my PIN on the SIM card first.

Need to dial out from PC to device having modem. device has Gadget serial. SO PC usb can be connected to usb of device and using driver can detect device as serial port. Now need to bypass dial out commands received over gadget serial port on device to modem connected via uart on device.

How can I configure pppd to do the same on the device via c++ code.

Hi,I just bought a usb modem ZTE MF195, and I am using Aero2 network (Poland).After googling, I found out how to setup this modem to work on Arch, but it only works with wvdial and it doesn't connect with NetworkManager.My config /etc/wvdial.conf:[Dialer Defaults] Modem = /dev/ttyACM0 Init1 = AT+CGDCONT=1,"IP","darmowy" Phone = *99# Carrier Check = yes Stupid mode = yes Us

I am a newbe to Linux. I need help with my "refurbished IBM ThinkCentre M50 Desktop w/installed 56k/modem (dial-up) w/Linux Ubuntu installed". I know "Windows"? I know there is a configuretion window for dial-up and how to do it but, not for Linux. Can someone help or send a manual of less than 30mbs? I would be great-full for any help. Bob

Okay, I'm running Ubuntu 11.04.

I bought a USB Extarnal Modem. Whice is controller based, I think thats a hard ware modem correct me if i'm wrong.

Right now I'm on windows and it shows the manufacturer is "Conexant" The thing is...how would I be able to use this in ubuntu. As I know winmodems does not work with linux.

Hello I am very very new to Linux so appreciate your replies in basic steps plaese. Installed suse 11.2(32 bits),KDE desktop. I Can't now figure out how to setup INTERNET. My internet connection is cable(part of ISP lan) without any modem/router etc. and it works fine on a win xp machine (using DHCP ip allocation).

[ubuntu] Dell USB modem 7 weeks 3 days ago

OK guys, this is getting beyond me, I cant get Ubuntu to use the DIAL up USB modem, I have gone through every post on this site regarding this type of modem, and have got nowhere fast.

am not a programmer so can anyone provide the commands to set the USB ports up so that Gnome PPP can see them?

All it sees is the com ports, my modem is listed as "dev/ttyACM0" and that is not showng up

I am using wvdial to connect to 3G network.

Sample conf is below. I want to add an if clause. If the Serial Number of the device is not my serial number it should not connect. Serial number can be shown by AT+CGSN.

How can I implement such "if ( AT+CGSN == 123456789 ); then" clause using wvdial? Can I?

I have installed hylafax on Ubuntu Server 8.04 with an external USRobotics modem. Everything is going fine. I use it almost as a fax2mail gateway. The fax is behind a PBX. The fax server receive every fax destinated to the internal fax N.1 (internal number 201)

I would like to make this. I have other internal fax machines connected to the PBX.