1

Network start issues in new build (with systemd v197)

view story
linux-howto

https://bbs.archlinux.org – I had the same problem setting up a new server. If you check the log for the unit file (journalctl -x -u network) you should see a 'Cannot find device "eno1"', which is a slightly more direct way of confirming the nature of the problem.As far as resolving it goes, I took a look at the dhcpcd@.service file, and it specifies:BindsTo=sys-subsystem-net-devices-%i.device After=sys-subsystem-net-devices-%i.deviceWhere %i is the string between the @ character and the suffix for instantiated unit files like dhcpcd@ (instantiated unit files are used like 'systemctl enable dhcpc (HowTos)

Tagmego's picture
Submitted by Tagmego on 01/28/2013

Stories similar to Network start issues in new build (with systemd v197)

I'm trying to write a service to start my network on an install without a network manager, but it seems that systemd doesn't like dhcpcd, and keeps sending it SIGTERM after it gets to a certain point.Here's the service:[Unit] Description=Connect to NETGEAR After=syslog.target

[Service] Type=oneshot ExecStart=/usr/sbin/iwconfig wlan0 essid NETGEAR key ********** ; /usr/sbin/dhcpcd w

This didn't help much.Now I have following status for eth0 and eno1eth0 dhcpcd@eth0.service - dhcpcd on eth0 Loaded: loaded (/usr/lib/systemd/system/dhcpcd@.service; enabled) Active: failed (Result: exit-code) since Thu 2013-05-09 11:23:52 CEST; 1min 31s ago Process: 350 ExecStart=/usr/sbin/dhcpcd -q -w %I (code=exited, status=1/FAILURE)

May 09 11:23:52 sunshine systemd[1]: dhcpcd@et

Hi there,I'm trying to start wpa_supplicant automatically when starting multi-user.target without going through something fancy like netcfg or NetworkManager. So I have done systemctl enable wpa_supplicant@wlan0Unforutnately, this doesn't work.

systemd, tmux and rTorrent 39 weeks 1 day ago

Check the journal after a reboot for error messages related to your rtorrent.service, like this:journalctl -b _SYSTEMD_UNIT=rtorrent.serviceor maybe this:journalctl -b | grep rtorrentJust a hunch (I could be wrong), but it's possible that during boot-up systemd tries to start rtorrent.service before the network is up, causing rtorrent to bail out.

I think the iphone has nothing to do with it.  A lot of people have been hit with network device naming issues lately.  From what I understand, the only solution and the only option long-term is to use a name other than ethX for all devices.  I moved to netX for my four wired nics:SUBSYSTEM=="net", ATTR{address}=="xx:xx:xx:xx:xx:xx", NAME="net0" SUBSYST

After some further troubleshooting I found that dhcpcd was not enabled systemctl enable dhcpcdnow gives;dhcpcd.service - dhcpcd on all interfaces      Loaded: loaded (/usr/lib/systemd/system/dhcpcd.service; enabled)      Active: active (running) since Mon 2013-03-18 12:08:00 GMT; 1min 19s ago     Process: 1073 ExecStart=/sbin/dhcpcd -q -b (cod

After my ISP read this Topic's posts they pointed me at link where it says I should comment the line noipv4ll in my /etc/dhcpcd.conf and I did it.Now I have different systemctl status of dhcpcd@eth0 which is, I hope, a good sign:[ibrahim@broislinux ~]$ sudo systemctl status dhcpcd@eth0 [sudo] password for ibrahim: dhcpcd@eth0.service - dhcpcd on eth0 Loaded: loaded (/usr/lib/systemd/sys

Network autostart 30 weeks 11 hours ago

Yesterday I installed ArchLinux and I really hate systemd. When I start my computer, I have no network connection and have to run dhcpcd to connect. I found this on wiki: # systemctl enable dhcpcd@eth0.serviceIt does not work. I have to run dhcpcd manually every time I start my computer.

PLANTROON https://bbs.archlinux.org/profile.php?id=62701

2012-10-20T07:30:44Z

Seems that way. Either a packaged unit file should be in /usr/lib/systemd/system or maybe a custom one in /etc/systemd/system. I have no privoxy.service in my set up. Does privoxy come with a unit service file? Don't use it myself. You can always create one.

swanson https://bbs.archlinux.org/profile.php?id=46056

2012-06-10T04:58:54Z