4

I have two working ethernet interfaces, but I can't host services like SSH, HTTP, etc

view full story
linux-howto

http://www.linuxquestions.org – Hello all, I have a quite interesting problem which I can't sort out by myself. Hopefully some of you have the necessary knowledge to help me out. I have two NIC's configured this way: feci@GEP0:/$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:c0:2e:2d:94 inet addr:192.168.0.198 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::21c:c0ff:fe2e:2d94/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:82565 errors:0 dropped:0 overruns:0 frame:0 TX packets:368242 errors:0 dropped:0 overruns:0 carrier:0 (HowTos)

jiqi2's picture
Submitted by jiqi2 on 09/27/2010 – Made popular on 09/27/2010

Stories similar to I have two working ethernet interfaces, but I can't host services like SSH, HTTP, etc

How can I make a correct /etc/network/interfaces for the following ifconfig output:

eth0 Link encap:Ethernet HWaddr 00:23:54:7e:2e:b6 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:1

Im new to virtualization and for the life of me cannot figure out how to get around this.

I have problem in my Ethernet after upgrade kernel to Quasar8000 2.6.30.8-67.eeepc.fc11. I can not connect to the Internet or open any site with the knowledge that everything is working well and the Ethernet adapter see the connection. the output for ifconfig is:

Code: eth0      Link encap:Ethernet  HWaddr 00:23:54:81:6D:33 

1- I just installed Fedora 12 on my Gateway laptop. It picked up my ethernet card w/o any problems, but it failed to pick up my wireless card. Below i cut and pasted the output of 'ifconfig -a", can someone help please. When you give instructions, please remember that i am new with all this.

[root@irvine etc]# ifconfig -a

And I can't upgrade to Ubuntu 10.10 because it said that there's a problem with my network connection. When there's none, since I am typing this now.

I have a VPN that I would like all traffic to go through except for a few specific ports such as ssh and webmin.

i have tried to get it working a few times without success. here is what i have:

eth0 Link encap:Ethernet HWaddr 1c:6f:65:c8:94:df inet addr:192.168.X.10 Bcast:192.168.X.255 Mask:255.255.255.0 inet6 addr: fe80::1e6f:65ff:fec8:94df/64 Scope:Link UP

ip route src not working 20 weeks 2 days ago

1I need to use several IPs on interface in Linux, and switch it, but it's not working. for example:

# ifconfig eth0 Link encap:Ethernet HWaddr 90:2b:34:33:80:65 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::922b:34ff:fe33:8065/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13220652 erro

So, my problem is that I just can't get IPv6 to work.

What does interrupt in eth0 mean? 26 weeks 23 hours ago

I wonder if "Interrupt" affects internet connection.

eth0 Link encap:Ethernet HWaddr 60:eb:69:6c:55:83 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45