1

bringing up interface eth0 rtnetlink

view story
linux-howto

http://www.unix.com – Hi all, OS: fedora release 10 when i try to restart network service, ending up with following errors. There are two interfaces eth0 and eth1 Code: bringing up interface eth0 rtnetlink answers file exists error adding <IP Address here> to eth0 bringing up interface eth0 rtnetlink answers invalid argument below are ifcfg-eth0 and eth1 files under /etc/sysconfig/network-scripts/ directory Code: # cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none BROADCAST=19.16.12.255 HWADDR=<MAC ADDRESS HERE> IPADDR=19.16.12.125 IPV6_AUTOCONF=yes (HowTos)

ziyi's picture
Submitted by ziyi on 10/10/2012

Stories similar to bringing up interface eth0 rtnetlink

Hi all,

OS: fedora release 10

when i try to restart network service, ending up with following errors.

Is it possible to have a second IP address on one interface (eg. eth0) - alias interface configuration - in a different subnet?

fc 17 missing ifcfg-eth0 20 weeks 3 days ago

Hello,

I am running Fedora release 17 (Beefy Miracle) and would like to set up a static IP address. I work with RHEL so I thought I would be able to locate a file /etc/sysconfig/network-scripts/ifcfg-eth0 but I have no such file on my system .

What's the use of /etc/sysconfig/network-scripts/ifcfg-eth* files ? In some cases ifconfig lists the interface eth0 but I don't find the corresponding ifcfg-eth0 file whereas in other instances if I create the ifcfg-eth1 file and restart the network like service network restart - this interface is not listed in ifconfig ??

I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1.

I can't ifdown an interface on a Debian 6.0.5 box;

user@box:/etc/network$ sudo ifdown eth0 && sudo ifup eth0 ifdown: interface eth0 not configured SIOCADDRT: File exists Failed to bring up eth0.

user@box:/etc/network$ cat interfaces auto lo iface lo inet loopback

allow-hotplug eth0 allow-hotplug eth1

auto eth0 iface eth0 inet static address 10.0.0.1 netmask 255.255.255.0 gateway 10.

I have a Linux network Bonding interface for two Ethernet interfaces (eth0 and eth1)

$ cat /etc/sysconfig/network-scripts/ifcfg-bond0 DEVICE=bond0 BOOTPROTO=static ONBOOT=yes IPADDR=XX.XX.XX.XX NETMASK=255.255.255.0 GATEWAY=XX.XX.XX.XXX

How i can add another IPADDR to this bonding Interface ?

Virtualbox centos no eth0 1 year 22 weeks ago

just installed a fresh centos-minimal and i can not get bridged network to work or any of the networks not even in host-only mode. when you run ifconfig there is no eth0 only a lo,

also when you cat /etc/sysconfig/network-scripts/ifcfg-eth0

DEVICE="eth0" HWADDR="08:00:27:FE:D5:10" NM_CONTROLLED="yes" ONBOOT="no"

I've just installed Centos 6.3 and I'm having trouble with my eth0 connection.

After I installed Centos 6.3 there was no eth0 file, so I made one.

inside my eth0 file I have:

DEVICE=eth0 IPADDR=xxx.xxx.x.xxx NETMASK=xxx.xxx.xxx.x ONBOOT=yes BOOTPROTO=static HWADDR=xx..... NM_CONTROLLED=no

When I run the cmd

# service network start

it brings up the loopback interface and the eth0 interface