1

Backtrack5 r3 reaver stuck after it is associated with 00:1F:C6:46:C4:65

view story
linux-howto

http://www.backtrack-linux.org – Hello guys! I just want to say that this thing is awesome i just wish that i could make it work because i really wanna make it work. So as you might know I am trying to test to get my wireless router WPA password by using backtracker 5 r3 reaver. I have followed many guides and i almost got it to work except its not actually trying to pin the router. Here is an example Code: root@bt:~# reaver -i mon0 -b 00:1F:C6:46:C4:65 -vv Reaver v1.4 WiFi Protected Setup Attack Tool Copyright (c) 2011, Tactical Network Solutions, Craig Heffner <cheffner@tacnetsol.com> [+] Waiting for be (HowTos)

Shoutmeloud's picture
Submitted by Shoutmeloud on 09/06/2012

Stories similar to Backtrack5 r3 reaver stuck after it is associated with 00:1F:C6:46:C4:65

Hiya I am using backtrack 5r3 Gnome 32 booting from CD on my Asus laptop

I have followed the instructions and when I do the final command root@bt:~# reaver -i mon0 -b 64:68:0C:59:2C:9A -vv

Reaver v1.4 WiFi Protected Setup Attack Tool Copyright (c) 2011, Tactical Network Solutions, Craig Heffner <cheffner@tacnetsol.com>

[+] Waiting for beacon from 64:68:0C:59:2C:9A [+] Switchin

Hello,

So I just downloaded a LiveCD (r3) and decided to give Reaver a go on my Macbook Pro using an RT73 USB wireless device I had.

I booted into the GUI and identified my wireless card on wlan1

I then ran

Code: airmon-ng start wlan1 to put it in monitor mode on mon0.

I used Code: airodump-ng wlan1 and picked the appropriate WPA encrypted MAC Address.

I ran reaver wi

Reaver question 36 weeks 3 days ago

I'm running backtrack5 R3 and currently testing reaver 1.4 Once it runs it get stuck at 90.90% first then 99.99%

On question I have is:

Does reaver need to get to 100% before finding anything or does 100% refer to any possible combination of 7 digits pin?

The reason why I'm asking is because if it get stuck at 90.90 and pin e.g.

Reaver Calculator 35 weeks 5 days ago

I thought some of you may find this nifty little Reaver tool helpful, basically you type in how your seconds per pin rate, and what % complete the attack is, the user is then presented with the MAXIMUM time it will take Reaver to crack the pin, it has a countdown timer built in, http://pastehtml.com/view/cek96ydvv.html

hi guys :) in this "video-recording"{yet another}I wanted to test the use of tool "reaver" content in BT5-r3 versus MY-AP (with-wps-enable) ....... nothing new! if you want to watch: http://vimeo.com/52650266 regards!

Hello, I hope this is the right section for my question.. I noticed that reaver starts trying pings starting from 00XX XXXX, the last six digits change somehow randomly but the first two increase in order.

I have successfully used Backtrack before with reaver, but as reaver is now being quite buggy for me, I've decided to try Fern Wifi Cracker. I installed backtrack 5 on VM (Ubuntu), and I have a WG111v2 for packet injection, which has worked successfully in the past. On backtrack 5r2 and r3, I have tried running Fern 1.6 and 1.7 versions. Everything works fine until I try to wifi attack.

Reaver problem/s 40 weeks 4 days ago

Hi there guys, well iv been trying out reaver on bt5v3. And so far iv got no luck out of it.

I checked some videos on youtube talks about how to install BT on diff linux tablets i.e. Galaxy Tab and really wonder if reaver, aircrack or whatever tools would be working just fine or let say detecting the wireless adapter (wlanXX) embedded in the tablet as a normal WiFi device to start the work? and if yes, will I expect the same performance as with Laptops and PCs??